Bentley Continental Key Fob Troubleshooting Tips
The Bentley Continental is an incredibly impressive car to drive. Its brushed-metal accents the center stack, while gorgeous leather and wood are used to cover the cabin. Its powerful W12 engine produces a whopping 552 break horsepower.
The Continental key fob is encased with rubber to prevent water from damaging its electronic chip. If it gets submerged by clean tap water or rain it is fine, however, prolonged exposure to salty water could harm it.
Keyless entry system
The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your vehicle using the remote control. This is convenient and allows you to save time and effort. But, there are a number of reasons for your key fob to cease to function. Some of these include dead batteries or water damage, as well as receiver module issues. In some cases, the problem could also be caused by a malfunction of the internal chip.
The key fob is encased with rubber to keep water from entering the electronic chips. However the key fob could be wet even if exposed to salt water or soapy water. This can damage the chip. It is important to clean the key fob and let it dry completely before placing the battery back. If the keyfob doesn't function after cleaning and letting it dry, then it's probably defective and requires replacement.
The metal clips on the battery of your Continental keyfob hold it in place and complete the circuit. If the clips are loosened or corroded, it can cause contact issues. This can be fixed by checking the battery contacts and making sure they are clean. Also, make sure that the battery is firmly installed. If you have a spare Continental key, test it to see if it is working. If the key is faulty then you can reprogram it with an OBDII scanner.
Battery
The key fob comes with a small coin battery inside. The remote will not work when the battery in the coin is dead. It is easy to determine the cause and replace it in only a few minutes. Water can also cause damage to the battery, and this requires the replacement. There are a few reasons that the key fob might not be working, including broken buttons, faulty battery contacts, signal interference or an inoperative receiver module. You can reset the system by disconnection of the 12 volt battery for a few minutes. This will allow the system to reset itself. Connect the positive cable first, then disconnect the negative.
The battery in the Bentley Continental key fob will last for four years based upon the frequency you use it. The battery comes with metal retaining clips that hold it in place and complete the circuit. The clips should be secured however if they're not then the remote will not operate correctly.
If the Continental keyfob is exposed clean water from the tap, it must be dried and cleaned using an absorbent paper towel prior to reinstalling the battery. If it is exposed to salt or soapy water, the chip may be damaged. In these cases, you will need to purchase a new key fob.
Water damage
David believes there aren't any major mechanical issues on this Continental, apart from minor rust damage to the wheel trims and surface corrosion that has been exposed to road grit. The boot is roomy and practical with a warning triangle from the factory strapped to the floor, as well as the space-saver spare wheel as well as a basic Bentley tools under the false floor.
The chip of the key fob is protected by rubber seals which should keep it functioning even when it's wet. However prolonged exposure to water can damage the chip, so it's advisable to take your key fob out of your purse when you go kayaking, swimming or rafting or other activities where it could be wet.
If your key fob was submerged in soapy water from the washing machine or submerged in ocean water at the beach, it may be worthwhile to get it back by cleaning the chip using isopropyl alcohol or an electronic cleaner. If the key fob isn't working after cleaning and drying it you might need to replace it. If you're in the market for a Bentley Continental key fob, make sure to select one that's water-resistant and fitted by the factory to your car.
Fault diagnosis
The Bentley Continental key fob lets you to lock and unlock your car with a click. This system is extremely convenient and offers security and safety when driving. However there are several things that can happen to your key fob. The most common causes are dead batteries water damage, or signal interference. If the key fob isn't working, there are a few troubleshooting actions you can take to pinpoint the issue.
The first thing to check is the battery. Make sure that it is well-placed and that the metal retaining clips are correctly positioned. If the clips are loose and the battery isn't get a good connection and will not work properly. The retaining clips should also be free of corrosion and clean.
Another reason for the key fob not working is an insufficient car battery. The 12 volt Continental battery should be in good shape to be able to communicate with your remote keyless entry system, and the rest of the electronics onboard. Check how much does a bentley key cost and recharge your car battery in the event of a need.
The Bentley Continental keyfob sends a message to the receiver module, which is located inside the ignition barrel. If the signal is not received it will cause the engine to not start and the alarm will sound. If the Bentley Continental key fob still doesn't work, you should consult a professional.